|
|
SVD-8: Distribution Panel with Differential Drive Engine
The SVD-8 distribution panel is a companion
product to the SVC-10 point-to-point distribution system. Adding an SVD-8
to the system expands the distribution capabilities from 1 to 8 locations
with IR capabilities at each location. It also doubles the distance
signals can be distributed to 2000 feet using CAT5 wire.
|
Pricing Information |
|
|
SVC-10 & SVC-10R: Point-To-Point S-Video Distribution
System
The new SVC-10 is designed
for CAT 5 or 5e structured wire installations. The SVC-10 is compatible
with both NTSC and PAL video standards. The two-piece SVC-10 system
consists of a rack mountable 1U transmitter with inputs for S-video,
composite, digital and analog audio along with a IR emitter jack and
RJ-45 output connector. Each input has auto-termination loop-thru for
connecting a local video/audio system. The miniature in-room receiver
has one RJ-45 input and one each of S-video, composite, digital and
analog audio outputs along with a 12 volt IR target input jack.
|
Pricing Information |
|
|
SVM-22 & SVM-24: S-Video Modulators
The new SVM
series of modulators offers complete MTS stereo encoding and S-video
inputs in a full component size rack mountable case. The SVM-22 and
SVM-24 are two and four channel stereo modulators with 25 dBmV of output
and easy push button programming. The SVM series incorporates S-video
inputs that support both S-video and composite video feeds with included
adapters. Offering full MTS stereo with dbx noise reduction and Dolby
Pro Logicฎ compatibility makes the SVMs perfect for integration into any
home theater system.
|
Pricing Information |
|
|
SVS-52: 5 Source Video/Audio Switcher
5 S-video/composite video
inputs; 5 digital/analog audio inputs
discreet IR codes for use with multiple identical products
composite to S-video conversion on all video inputs
cross conversion of optical and coax digital inputs
IR and RS-232 control interfaces
front panel convenience inputs
included remote control
direct source selection
IR learning capabilities
broadcast quality switching
auto/manual seek modes
|
Pricing Information |
|
|
2010 & 2100A: Wall Plates
The 2100 series is available in numerous
models and configurations. Users can select from infrared interfaces,
targets, emitters, and expansion blocks.
The infrared interface wall plate, model 2100A, is used with the 12volt
DA-550 distribution panels to allow IR control from any room on the
system. The 2100A is bi-directional and can input as well as output IR
information. The 2100A will accept any 12 volt target using the input
jack or three wire screw terminal. Hint: when using a 12 volt IR system
and 2100A's are not at all locations a DC block, model 2105, must be
used on the coax.
The 2010 interface wall plate has two functions. First it will remotely
power the DA-550 and DA-8200 series panels from up to 75' away. Second
when using a modulator with IR output the 2010 will break out the IR
signals from a 2100A present on the coax and pass them to connected
emitters.
|
Pricing Information |
|
|
2171/ 2172/ 2173: IR Repeaters/Emitters
IR emitters are both 5 and 12 volt
compatible. Use the IR emitters over the IR sensors on video products
like VCRs, DVDs and music systems to control their functions with IR
commands. The Emitters are used with other 2100 series products for
whole-house IR control.
2171:
single IR pass head - 5' cord with mono mini plug
2172: dual head - 5' cord with mono
mini plug
2173: single solid head - 5' cord
with mono mini plug
|
Pricing Information |
