|
|
2010 : Wall Plates
The 2010 interface wall plate has two
functions. First it will remotely power the DA-550 and DA-8200 series
panels from up to 75' away. Second when using a modulator with IR output
the 2010 will break out the IR signals from a 2100A present on the coax
and pass them to connected emitters.
|
Pricing Information |
|
|
2100a : Wall Plates
The infrared interface wall plate, model
2100A, is used with the 12volt DA-550 distribution panels to allow IR
control from any room on the system. The 2100A is bi-directional and can
input as well as output IR information. The 2100A will accept any 12
volt target using the input jack or three wire screw terminal. Hint:
when using a 12 volt IR system and 2100A's are not at all locations a DC
block, model 2105, must be used on the coax.
|
Pricing Information |
|
|
2130A/ 2131/ 2132/ 2133: IR Remote Targets
INFRARED VIA COAX CABLE
Control any video or
audio product (VCR, satellite receiver, DVD, etc.) from any location in
the house. Regardless of where the product is located, the user simply
aims an infrared remote control at the target and presses a button. The
infrared codes emitted from the remote control are transmitted through
the home's coaxial cable and instantly repeated by each infrared
repeater/emitter connected to the system. Infrared codes sent via the
coax are far more reliable and free of interference than infrared
transmitted through the air. There is no need for any additional wires!
In order to use the 2100 series 12-volt and 5 volt components, it is
necessary that a DA-550 (12volt) or DA-8200 (5volt) series coaxial cable
panel be used in the system. It provides power to all of the system IR
components and ensures that the signals are passed from targets to
emitters.
12 VOLT SYSTEMS
2130A:
mini target- talk back LED - 7' cord
terminated in stereo mini plug
2131:
in-wall target - talk back LED
2132:
set top target - 7' cord terminated in stereo mini plug
5 VOLT SYSTEMS
2133:
set top target - dual F connections
|
Pricing Information |
|
|
2171/ 2172/ 2173: IR Repeaters/Emitters
IR emitters are both 5 and 12 volt
compatible. Use the IR emitters over the IR sensors on video products
like VCRs, DVDs and music systems to control their functions with IR
commands. The Emitters are used with other 2100 series products for
whole-house IR control.
2171:
single IR pass head - 5' cord with mono mini plug
2172: dual head - 5' cord with mono
mini plug
2173: single solid head - 5' cord
with mono mini plug
|
Pricing Information |
|
|
2174 & 2184: IR Expansion
The 2174 expansion takes
the output of a single emitter jack and extends it into 4 emitter jacks.
The 2184 coax panel expansion jack allows local IR access on a DA-550 or
DA-8200 series panel. IR information is available at the panel on the
three pin power connector. Clip on a the 2184 and up to 4 single head
emitters may be connected directly to the 2184.
|
Pricing Information |
|
|
2181: IR Coaxial Cable Panel Expansion Link
Use the model 2181 IR expander to send
IR control signals from one DA-550 or DA-8200 to another DA-550 or
DA-8200. Using a master DA-550 or DA-8200 and adding up to eight slave
units, IR control signals will not be passed from master units to the
slave units unless a model 2181 is used at each slave
DA-550 or DA-8200 panel. The 2181 allows each TV with a target that is
connected to the slave unit, to send IR signals back to the audio/video
devices connected to the master DA-550 or DA-8200.
|
Pricing Information |
