The IM-313 Nutone radio-intercom is an older unit that is easily replaced by the current IM-3303 system or M & S DMC3-4 which offers the opportunity of CD music and stereo speakers. Both system were a 3 wire system. This means that you will be able to use your existing wiring when installing your new system. Below is a list of the old items and the replacement procedure. The first section if for the Nutone upgrade, below will be the section for the M & S DMC3-4 upgrade.
Original Nutone System |
Suggested Nutone Replacement |
|
IM-313 Master
|
IM-3303 Master
|
Both of these systems are a 3-wire system. That means that you will be able to use your existing wiring. The IM-3303 is not large enough to cover the old hole, but there is a cover plate available that will cover the hole if you are not planning on remodeling. There is a version for the IM-3303 or for the IM-3303 and the CP-95 tape unit. |
IR-11 Rough-in |
IR-104 Rough-in
|
The IR-104 rough-in is 14 1/4" long and 7" high. You would center this height wise in the hole if you are using the update frame. The rough-in is what holds the update frame in place. |
IS-35 Inside Speaker
|
IS-335 |
The IS-335 is large enough to cover the hole and footprint of the old speakers. |
IR-5 Rough-in |
IR-50 |
To install the IR-50, you will have to open up your existing hole by approximately 1" on the sides and 1" on the top. |
IS-38 Inside Speaker
|
IS-338 with IA-83 Frame |
Nutone has made an update frame called the IA-83 that will screw into the old IR-8 rough-in. This then enables you to mount the IR-80 rough- in for the IS-338 into the IA-83 adapter frame. Since you will be using your old rough-in to hold the adapter frame, there is no wall work required. This makes the change out easy. |
IC-31 Outside controls
|
IC-331W |
Your controls should be surface mounted, if so they are easily replaceable by the surface mount IC-331W |
IC-31 Control |
IC-301 Control |
The IC-31 was mounted in a 3 gang electrical box. It can be replaced with either an IC-301 or IC-331. The IC-301 is the easiest to install because it has a larger foot print than the IC-331. The IC-301 can be recessed using an IR-81 rough-in frame. To use the IC-331 you will need to measure your hole. The IC-331 measure 7" wide and 4" high. For outside surface mounting the IC-31 was mounted in a brown box, this can be discarded and replaced with an IC-301W or IC-331W which are also surface mounted unit |
IS-37 Clock Speaker |
IS-338 Speaker |
You will need to remove the old rough-in and replace it with the IA-83 adapter and the IR-80 to mount the IS-338. You gain a bigger speaker, but loose the clock. |
ISA-36 Desk Top Speaker
|
IS-335 with IA-60 Surface Mount Frame |
You would remove the black IA-6C cord from your desk speaker and connect it to the IS-335. This then mounts into the IA-60 desk top adapter. |
IS-34 Desk Top Clock Speaker
|
IS-335 with IA-60 Surface Mount Frame |
You would remove the black IA-6C cord from your desk speaker and connect it to the IS-335. This then mounts into the IA-60 desk top adapter. |
IS-79 Outside Speaker |
You can use the old speaker with the new system. |
|
ISA-77 Patio Speaker
|
You can use the old speaker with the new system. | |
IS-78 |
You can use the old speaker with the new system. |
The M & S system offers an add-on 6-disc CD player and the option of adding stereo music via the MC960A amplifier.
Original Nutone System | Suggested M&S Replacement | |
IM-313 Master
| DMC3-4
| The DMC3-4 is designed to work with your existing
speaker wires.
The DMC3-4 also gives you the option of true stereo with the MC960A amplifier |
IR-11 Rough-in | DMC1H ..for use with DMC3-4DMC1HC..for use with DMC3-4 and DMC1CD compact disc player
| The DMC1H is designed to be used with the DMCFR trim
plate. It will not cover the area of the IM-313. The DMCFC is the trim plate for the
DMC1HC. The DMC1HC is 15-5/8" tall and will be close to covering the hole. The DMC3-4 requires 110V power to be run to the mounting box. This may or may not be the case with the IM313. It would need to be field verified. |
| Procedure for stereo speaker | To achieve true stereo music, you will need to extend your speaker wires to the nearest open location. There they will be connected to the MC960PA stereo amplifier. The MC960PA can be mounted in the basement or a closet and connect to the DMC3-4 via the MS7XSC cable. | |
IS-35 Inside Speaker  | DMC3R | The DMC3R is used with the DMCFR to attach to the current metal rough-in frame and cover the old hole. It makes a very easy and quick change out. |
IS-38 Inside Speaker  | IS-79MOD | The IS-79 is a speaker that can be painted to match your room.
It comes with a volume control (not shown) for music only. It will mount to
your existing metal frame If intercom is desired, you would need to use the DMC3R with the DMC1HR frame and do some wall patching. |
ISA-39 Outside Speaker
| DMC4RSW with DMC1HRWS mounting box | This is a surface mount unit and will replace your old ISA-39 |
IS-37 Clock Speaker | IS-79MOD | The IS-79 is a speaker that can be painted to match your room.
It comes with a volume control (not shown) for music only. It will mount to
your existing metal frame If intercom is desired, you would need to use the DMC4R with the DMC1HR frame and do some wall patching. |
ISA-36 Desk Top Speaker
| DMC4RS with DMC1HRWS mounting box | You would remove the black IA-6C cord from your desk speaker and connect it to the DMC4RS. Then you can use the DMC1HRWS surface mount frame. It will not tilt up, but it will sit on the desk. |
ISB-34 Desk Top Clock Speaker
| DMC4RS with DMC1HRWS mounting box | You would remove the black IA-6C cord from your desk speaker and connect it to the DMC3RS. Then you can use the DMC1HRWS surface mount frame. It will not tilt up, but it will sit on the desk. |
ISA-77 | NW8
|
The NW8 will replace the ISA-77 and surface mount. |
Surface mount Door Speaker | DB3 door speaker with DMCFD frame | The DMCFD update frame mounts to the existing metal frame for easy installation. |
recessed Door Speaker | DB3 door speaker with DMCFD frame | The DMCFD update frame mounts to the existing metal frame for easy installation |
IC-31 Control | DMC3RW outdoor speaker with DMCFRW | M & S does not make a control only, so you can replace the control with the DMC3RW speaker with the DMCFRW update frame. |
IS-78 | You can use the old speaker with the new system. | The IS-79 Can be reused with the exception of the speaker cone. It will need to be changed out to a 45 ohm cone available thru R & I. |
IS-79 Outside Speaker | IS-79 mod | The IS-79 Can be reused with the exception of the speaker cone. It will need to be changed out to a 45 ohm cone available thru R & I |
